Fully synthetic diesel oil
Fully synthetic diesel oil
Component:
the product uses imported synthetic oil as the base oil. This product is made of refined foreign advanced technology and production technology. It applies to the vast majority of European. American and Asian models. It provides comprehensive engine protection. offectively improves and prolongs the service life of the engine. and is particularly outstanding in terms of fuel officiency. friction loss and durability. meeting the current advanced level of API/CI for engine lubrication.
Quality index:
| Item | Index | Test method | |||
|---|---|---|---|---|---|
| Product rating | CI | — | |||
| Viscosity grade (according to GB/T14906） | 0W/30 | 0W/40 | 5W-50 | — | |
| Kinematic viscosity （100℃），（mm2/s） | 9.3-＜12.5 | 12.5-16.3 | 16.3-21.9 | ASTM D445 | |
| Low temperature dynamic viscosity .mPa.s(℃）no greater than | Measured | Measured | Measured | ASTM D5295 | |
| Boundary pumping temperature.℃ not higher than | —30 | —30 | — | ASTM D3829 | |
| Viscosity index not less than | 135 | 140 | 145 | ASTM D2270 | |
| Flash point(opening)℃ not lower than | 220 | 235 | 245 | ASTM D92 | |
| Pour point /℃ not higher than | -50 | -45 | -35 | ASTM D97 | |
| Foam nature (foam tendency/Foam stability)（mL/mL） | 24℃ no greater than | 25/0 | ASTM D892 | ||
| 93.5℃ no greater than | 150/0 | ||||
| Rear 24℃no greater than | 25/0 | ||||
| Mechanical impurities/% no greater than | 0.01 | ASTM D473 | |||
| Moisture/% no greater than | trace | ASTM D95 | |||
| Residual carbon(before dosing)% | report | ASTM D4530 | |||
| Suifate Ash% | report | ASTM D874 | |||
| Total alkali number mgKOH/g | report | ASTM D2896 | |||
| Sulfur/% | report | ASTM D4294 | |||
| Phosphorus/% | report | IPI49/8031 | |||
| calcium/% | report | ISO2192 | |||
| Zinc/% | report | IP117/74 | |||
| magnesium/% | report | SH/T0061 | |||
| ammonia/% | report | GB/T9170 | |||
| Oil tile corrosion test | Oil weight loss，mg， no greater than | 50 | SH/T 0265 | ||
| Piston skirt paint film score | 9.0 | ||||
| Shear stability Kinematic viscosity(100℃），mm2/s | Within the oil viscosity range | SH/T0265GB/T265 | |||
|
High temperature detergency and abrasion resistance test Top ring groove carbon deposition volume% no greater than weighted total score no greater than Piston ring side gap loss mm no greater than |
45 140 0.013 |
UDC621 892 098 GB/T 9932 |
|||
Note:
the recommended range . use and precautions
1.0W-30 oil which can meet the Japanese and the small amount of exhaust gas turbocharged. Korean. and other European and US-based models. 0W-40.5W-50 for large displacement. motor vehicle oil and other models.
2.Befor using this oil. put other oil on the net before adding the oil(do not mix it with other oil to prevent the use effect)
3.Oil change cycle up to 15000~18000km
Product packaging:
Iron drum 170kg packaging. 18 liters in the barrel. kog packaging 4 liters..
-
HN-69-1 Emulsification Cutting fluid -
HN-M9 Machining Center Emulsification Cutting fliud -
HN-R1 Grinding & Antirust Emulsification Cutting fliud -
HN-R1A Grinding & Antirust Emulsification Cutting fliud -
HN-R1B Line Cutting Emulsification fliud
-
HN-R1C Copper Wire Drawing fluid
