Welcome to Jiangsu JieDa Oil Co., Ltd.
江苏捷达油品有限公司
Jie Da Hotline :+86-519-85957118
ProductsJie Da Oil
Location : Homepage / Products / Car oil series / Fully synthetic gasoline engine oil

Fully synthetic gasoline engine oil

Fully synthetic gasoline engine oil

 

Component:

the product uses imported synthetic oil as the base oil, and introduces foreign high-performance additives, the product is specially formulated for most car models in Europe, the United States and Asia. It provides comprehensive engine protection and effectively improves and extends engine life. It is particularly prominent in tems of fuel efficiency, friction loss and durability, meeting the current advanced APISN/ILSAC GF-5 engine lubrication rating standards.

 

Quality index:

Item
Index
Test method
Product rating
SN
——
Viscosity grade (according to GB/T 14906)
0W/20
0W/30
0W-40
——
Kinematic viscosity (100℃),(mm²/s)
5.6~9.3
9.3~12.5
12.5~16.5
ASTM D445

Low temperature dynamic

viscosity .mPa.s(℃)                         no greater than

Measured
Measured
Measured
ASTM D5293
Boundary pumping temperature.℃ not higher than
—30
—25
—20
ASTM D3829
Viscosity index                      not less than
140
145
150
ASTM D2270
Flash point (opening) /℃               not lower than
220
230
235
ASTM D92
Pour point /℃             not higher than
-55
-50
-45
ASTM D97

Foam Properties

(FoamPropensity/Foam

Stability)(mL/mL)

24℃    no greater than
25/0
ASTM D892
93.5℃   no greater than
150/0
Rear24℃no greater than
25/0
Mechanical impurities/%        no greater than
0.01
ASTM D473
Moisture/%              no greater than
trace
ASTM D95
Residual carbon(before dosing)%
report
ASTM 4530
Sulfate Ash%
report
ASTM D874
Total alkali number mg KOH/g
report
ASTM D2896
sulfur/%
report
ASTM D4294
phosphorus/%
report
IP 149/80
calcium/%
report
ISO 2192
barium/%
report
ISO 2192
Zinc/%
report
IP 117/74


Note:

the recommended range, use and precautions

1. 0W-20W,0W-30W can meet the oil and the small amount of exhaust gas turbocharger of Japanese, Korean, and other European and US-based models, 0W-40 displacement for large, heavy vehicles Other models of oil.

2. Before using this oil, put other oil on the net before adding the oil (be careful not to mix it with other oil to prevent the lowering effect).

3. The oil at ambient temperature of about 40 degrees below zero, oil change up to 18,000~20,000km.


Product packaging:

Iron drum 200L packaging, 18L liters in the barrel, keg packaging 4L liters.

此页面上的内容需要较新版本的 Adobe Flash Player。

获取 Adobe Flash Player

相关产品
  • HN-69-1 Emulsification Cutting fluid
    HN-69-1 Emulsification Cutting fluid
  • HN-M9 Machining Center Emulsification Cutting fliud
    HN-M9 Machining Center Emulsification Cutting fliud
  • HN-R1 Grinding & Antirust Emulsification Cutting fliud
    HN-R1 Grinding & Antirust Emulsification Cutting fliud
  • HN-R1A Grinding & Antirust Emulsification Cutting fliud
    HN-R1A Grinding & Antirust Emulsification Cutting fliud
  • HN-R1B Line Cutting Emulsification fliud
    HN-R1B Line Cutting Emulsification fliud
  • HN-R1C Copper Wire Drawing fluid
    HN-R1C Copper Wire Drawing fluid
Top